[1]申云,陆静,刘瑞亮.软质印章石抛光工艺[J].华侨大学学报(自然科学版),2020,41(4):428-433.[doi:10.11830/ISSN.1000-5013.201910060]
　SHEN Yun,LU Jing,LIU Ruiliang.Polishing Technology of Soft Seal Stone[J].Journal of Huaqiao University(Natural Science),2020,41(4):428-433.[doi:10.11830/ISSN.1000-5013.201910060]
点击复制

软质印章石抛光工艺()
分享到：

《华侨大学学报（自然科学版）》[ISSN:1000-5013/CN:35-1079/N]

卷:
第41卷
期数:
2020年第4期
页码:
428-433
栏目:
出版日期:
2020-07-20

文章信息/Info

Title:
Polishing Technology of Soft Seal Stone
文章编号:
1000-5013(2020)04-0428-06
作者:
申云1;  陆静1;  刘瑞亮2
1.华侨大学 制造工程研究院, 福建 厦门 361021;2. 厦门大学 机电工程系, 福建 厦门 361101
Author(s):
SHEN Yun1;  LU Jing1;  LIU Ruiliang2
1. Institution of Manufacture Engineering, Huaqiao University, Xiamen 361021, China; 2. Department of Mechanical and Electrical Engineering, Xiamen University, Xiamen 361101, China
关键词:
粗糙度;  光泽度;  表面形貌;  印章石;  机械抛光
Keywords:
roughness;  gloss;  surface topography;  seal stone;  mechanical polishing
分类号:
TG356.28
DOI:
10.11830/ISSN.1000-5013.201910060
文献标志码:
A
摘要:
为了提升软质印章石的加工质量,在不同型号砂纸和溶胶-凝胶(SG)抛光膜上磨抛巴林石、高山石、芙蓉石3种印章石,探讨研磨盘和载物盘的转动方向、转速,加工压力,加工时间等工艺参数及工艺路线,并确定每道工序的最大光泽度值,以及印章石表面形貌和粗糙度之间的关系.结果表明:最终优化工艺的研磨盘、载物盘分别以300,120 r·min-1同向转动,加工压力为15 MPa;最佳工艺路线是通过在400#砂纸半精磨、在2 000#砂纸的精磨和在SG抛光膜上抛光,使印章石表面光泽度达到50以上,粗糙度在100 nm左右,表面形貌在放大100倍时无明显划痕.
Abstract:
In order to improve the processing quality of soft seal stone, the processing technology was studied. Three kinds of seal stones: Balin Stone, Gaoshan Stone and Furong Stone were polished on different types of sandpaper and sol-gol(SG)polishing film. The technological parameters covered the direction and speed of grinding disc and loading disc, the processing pressure,the processing time and processing routes. In addition, the maximum glossiness of every step and the relationship between the surface topography and roughness of the seal stones are determined. The result shows that the grinding disc and loading disc are rotated in the same direction at 300 r·min-1and 120 r·min-1 respectively in an optimized processing. The corresponding processing pressure is 15 MPa. The best processing route is semi finishing with 400# sandpaper first, then finishing with 2 000# sandpaper, and finally polishing on SG polishing film, which makes the surface glossiness of seal stones more than 50, the roughness about 100 nm, and the final surface without obvious scratches when magnified 100 times.

参考文献/References:

[1] 王剑民,王姝琼.印章石[J].西部源,2014(6):64-67.
[2] 李丹.印章石(寿山石)品种、雕刻实践及工艺评价[D].北京:中国地质大学,2012.
[3] 徐春茂.中国四大印章石之二: 寿山石[J].中国地名,2008(5):65-69.
[4] 隋德,潘险峰,杨春林,等.巴林石[J].中国标准导报,2014(9):64-67.
[5] 福州寿山石鉴定中心.寿山石[J].中国标准导报,2016(12):50-54.
[6] 刘金彩,曾利群.石材的维护和保养[J].石材,2005(3):46-48.DOI:10.14030/j.cnki.scaa.2005.03.014.
[7] 封黎明.石材表面的维护和保养[J].中国洗涤用品工业,2012(1):70-71.DOI:10.16054/j.cnki.cci.2012.01.002.
[8] ZHANG Heng,ZHANG Jinsheng,CHEN Ming,et al.The effect of operational parameters on diamond tools of frame sawing system: Wear characteristics and optimization in stone processing[J].International Journal of Refractory Metals and Hard Materials,2019,84:1-8.DOI:10.1016/j.ijrmhm.2019.105019.
[9] 周平.石材加工技术发展与设备选型[J].江西建材,2017(4):270-273.
[10] 齐自成.薄型/超薄型石材加工技术及应用[J].山东建材,2003(2):46.
[11] 罗桂海.新型石材研磨抛光技术与基体特性研究[J].现代制造技术与装备,2019(6):13-14,16.DOI:10.16107/j.cnki.mmte.2019.0548.
[12] 辜洋建,周瑶琪,王翠芝,等.老挝石和寿山石矿物学特征的差异性研究[J].地质与资源,2018,27(6):554-565.DOI:10.13686/j.cnki.dzyzy.2018.06.008.
[13] ABDRAKHIMOV V Z.Study of the limiting shear stress of pyrophyllite-clay component-water composition at elevated temperature[J].Refractories and Industrial Ceramics,2019,60(4):373-375.DOI:10.1007/s11148-019-00370-6.
[14] 严俊.叶腊石矿物学特征及其应用研究[D].杭州:浙江工业大学,2012.
[15] 王一帆.寿山芙蓉石[J].福建农机,2011(4):53.
[16] 卜范广.“钝刀削木”的启示: 浅谈石材加工中存在的几个问题[J].石材,2009(1):18-20.DOI:10.14030/j.cnki.scaa.2009.01.005.
[17] 李震.印章石振动抛光工具的制备及其应用的研究[D].厦门:华侨大学,2019.
[18] ZENG S,BLUNT L.An experimental study on the correlation of polishing force and material removal for bonnet polishing of cobalt chrome alloy[J].International Journal of Advanced Manufacturing Technology,2014,73(1/2/3/4):185-193.DOI:10.1007/s00170-014-5801-z.
[19] RAO Zhimin,GUO Bing,ZHANG Quanli,et al.Form error compensation in soft wheel polishing by contact force optimization[J].International Journal of Advanced Manufacturing Technology,2017,91(1/2/3/4):1197-1207.DOI:10.1007/s00170-016-9798-3.
[20] 吴玉厚,吴岗,陆峰,等.国内外异型石材机械的现状及发展趋势[J].石材,2008(3):22-25.DOI:10.14030/j.cnki.scaa.2008.03.006.

相似文献/References:

[1]黄辉,徐西鹏.磨抛中金刚石磨盘与花岗石的界面作用[J].华侨大学学报(自然科学版),2003,24(4):390.[doi:10.3969/j.issn.1000-5013.2003.04.011]
　Huang Hui,Xu Xipeng.Interfacial Reaction between Diamond Disk and Granite during Vertical Spindle Grinding[J].Journal of Huaqiao University(Natural Science),2003,24(4):390.[doi:10.3969/j.issn.1000-5013.2003.04.011]
[2]王建军.花岗石磨抛光的表面光泽度特性[J].华侨大学学报(自然科学版),2007,28(3):225.[doi:10.3969/j.issn.1000-5013.2007.03.001]
　WANG Jian-jun.The Study on Glossiness Characteristic of Granite Polished Surface[J].Journal of Huaqiao University(Natural Science),2007,28(4):225.[doi:10.3969/j.issn.1000-5013.2007.03.001]

备注/Memo

备注/Memo:
收稿日期: 2019-11-05
通信作者: 陆静(1981-),女,教授,博士,主要从事纳米碳材料表面改性、新型研磨抛光工具制备、光电材料基片的超精密加工的研究.E-mail:lujing26@hqu.edu.cn
基金项目: 国家自然科学基金资助项目(U1805251); 福建省科技计划项目(2018I0012); 福建省厦门市科技计划项目(3502Z20173049); 华侨大学研究生科研创新培高项目(18013080025)
更新日期/Last Update: 2020-07-20